electrical theory and electrical fundementals for all electrical related people . students , engineers, electrician #electricaltheorems,electrical,

Tuesday, 25 November 2014

itemprop='blogPost' itemscope='itemscope' itemtype='http://schema.org/BlogPosting'>

ELECTRIC CURRENT

electrical theory and electrical fundementals for all electrical related people . students , engineers, electrician #electricaltheorems,electrical,


An electric current can be broadly defined as charged particles in motion - a flow of charge. The most obvious effect of a current would seem to be the transfer of charge from one place to another. So it is, when a charged body is discharged by touching it with an earthed wire, or when lightning strikes a tree. However, it is important to realise that most currents flow in closed loops or circuits with no net transfer of charge. When there is a steady current the distribution of charge around a circuit remains constant and every part of the circuit remains substantially neutral.

The effects of electric current 

You can't see anything move in an electric current but currents do have a number of extremely important effects, which can be broadly classified as shown in the first column of table 3.1. This list is by no means exhaustive. Some of the topics are discussed in later chapters. In this chapter we are concerned in general terms with the charge, mass and energy transferred by a current

The measurement of electric current


Electric current is measured by means of a device which responds quantitatively to one or other of the effects of the current. Because current is a flow of charge, the device usually has to be connected so that the current goes through it.
Each system has advantages and disadvantages. The choice is determined by the exigencies of the situation. For example a clip-on ammeter does not require the interruption of the current, but it is bulky and not very sensitive. By contrast a digital ammeter responds quickly. Moving coil meters have the advantage of simplicity and long-term stability.

Movement of charge

Any movement of charge constitutes an electric current. The charge carriers could be electrons in a vacuum, electrons in a metal, 'holes' in a semiconductor or ions in a solution. The charge may move in free space, through a conductor or on a conveyor belt. An obvious manifestation of charge movement is an electric spark. At each spark some charge is transferred. Together a sequence of sparks makes up an intermittent current in which each spark contributes a current pulse. If the spark gap is narrowed so that the sparks become more frequent, they tend to merge to make a continuous current. 

Definition and unit of current 

The value of a current in a wire at any point is defined to be equal to the rate of flow of net positive charge past that point. The direction of the current is defined to be the direction of flow of positive charge.
            If the charge carriers are actually negative then the direction of the current is opposite to the flow direction of the particles. Thus a current of one ampere to the right could be either positive charge flowing to the right at 1 coulomb per second or negative charge flowing to the left at 1 coulomb per second, or some combination of flows in both directions such 0.5 C.s-1 each way.
The SI unit of electric current is the ampere (symbol A), equal to one coulomb per second. Because current is easier to measure than charge, the physical standards have been established using current as the base quantity, so the coulomb is defined as an ampere-second (A.s). The ampere is defined in terms of magnetic effects 

Current 

When there is an electric current in a circuit, energy is generally being transferred from a source to a load: energy is transferred from a battery to a lamp or from a nerve cell to measuring electrodes. In such circuits, the current is associated with the energy transfer.

Monday, 24 November 2014

itemprop='blogPost' itemscope='itemscope' itemtype='http://schema.org/BlogPosting'>

SPEED CONTROL OF DC SERIES MOTOR

electrical theory and electrical fundementals for all electrical related people . students , engineers, electrician #electricaltheorems,electrical,

Speed Control of Series Motors

1. Flux Control Method: 

: Variations in the flux of a series motor can be brought about in any one of the following ways:

 (a) Field Diverters:

 The series winding are shunted by a variable resistance known as field diverter. Any desired amount of current can be passed through the diverter by adjusting its resistance. Hence the flux can be decreased and consequently, the speed of the motor increased.

 (b) Armature Diverter:

A diverter across the armature can be used for giving speeds lower than the normal speed. For a given constant load torque, if Ia is reduced due to armature diverter, the  must increase (∵TaIa ) This results in an increase in current taken from the supply(which increases the flux and a fall in speed (N  I/ )). The variation in speed can be controlled by varying the diverter resistance.















(c) Trapped Field Control Field: This method is often used in electric traction. The number of series filed turns in the circuit can be changed. With full field, the motor runs at its minimum speed which can be raised in steps by cutting out some of the series turns.
 (d) Paralleling Field coils: this method used for fan motors, several speeds can be obtained by regrouping the field coils. It is seen that for a4-pole motor, three speeds can be obtained easily.









 Variable Resistance in Series with Motor















By increasing the resistance in series with the armature the voltage applied across the armature terminals can be decreased. With reduced voltage across the armature, the speed is reduced. However, it will be noted that since full motor current passes through this resistance, there is a considerable loss of power in it.

Sunday, 23 November 2014

itemprop='blogPost' itemscope='itemscope' itemtype='http://schema.org/BlogPosting'>

LIGHT EMITTING DIODE (LED)

electrical theory and electrical fundementals for all electrical related people . students , engineers, electrician #electricaltheorems,electrical,






















To explain the theory and the underlying principle behind the functioning of an LED
The first known report of a light-emitting solid-state diode was made in 1907 by
the British experimenter H. J. Round. In the mid 1920s, Russian Oleg Vladimirovich Losev independently created the first LED, although his research was ignored at that time.
• In 1955, Rubin Braunstein of the Radio Corporation of America reported on infrared emission from gallium arsenide (GaAs) and other semiconductor alloys.
• Experimenters at Texas Instruments, Bob Biard and Gary Pittman, found in 1961 that gallium arsenide gave off infrared radiation when electric current was applied. Biard & Pittman received the patent for the infrared light-emitting diode.

• In 1962, Nick Holonyak Jr., of the General Electric Company and later with the University of Illinois at Urbana-Champaign, developed the first practical visible spectrum LED. He is seen as the "father of the light-emitting diode".
• In 1972, M. George Craford, Holonyak's former graduate student, invented the first yellow LED and 10x brighter red and red-orange LEDs.
• Shuji  Nakamura of Nichia Corporation of Japan demonstrated the first high brightness blue LED based on In GaN. The 2006 Millennium Technology Prize was awarded to Nakamura for his invention.

THEORY

A Light emitting diode (LED) is essentially a pn junction diode. When carriers are injected across a forward-biased junction, it emits incoherent light. Most of the commercial LEDs are realized using a highly doped n and a p Junction.
To understand the principle, let’s consider an unbiased pn+ junction band . The depletion region extends mainly into the p-side. There is a potential barrier from Ec on the n-side to the Ec on the p-side, called the built-in voltage, V0. This potential barrier prevents the excess free electrons on the n+ side from diffusing into the p side.
When a Voltage V is applied across the junction, the built-in potential is reduced from V0 to V0 – V. This allows the electrons from the n+ side to get injected into the p-side. Since electrons are the minority carriers in the p-side, this process is called minority carrier injection. But the hole injection from the p side to n+ side is very less and so the current is primarily due to the flow of electrons into the p-side. Appendix 1) results in spontaneous emission of photons (light). This effect is called injection electroluminescence. These photons should be allowed to escape from the device without being reabsorbed.
The recombination can be classified into the following two kinds


• Direct recombination

• Indirect recombination

Direct Recombination:

In direct band gap materials, the minimum energy of the conduction band lies directly above the maximum energy of the valence band in momentum space energy 

. In this material, free electrons at the bottom of the conduction band can recombine directly with free holes at the top of the valence band, as the momentum of the two particles is the same. This transition from conduction band to valence band involves photon emission (takes care of the principle of energy conservation). This is known as direct recombination. Direct recombination occurs spontaneously. GaAs is an example of a direct band-gap material.

Indirect Recombination

In the indirect band gap materials, the minimum energy in the conduction band is shifted by a k-vector relative to the valence band. The k-vector difference represents a difference in momentum. Due to this difference in momentum, the probability of direct electronhole recombination is less. In these materials, additional dopants(impurities) are added which form very shallow donor states. These donor states capture the free electrons locally; provides the necessary momentum shift for recombination. These donor states serve as the recombination centers. This is called Indirect (non-radiative) Recombination.

 E-k plot of an indirect band gap material and an example of how Nitrogen serves as a recombination center in GaAsP. In this case it creates a donor state, when SiC is doped with Al, it recombination takes place through an acceptor level. The indirect recombination should satisfy both conservation energy, and momentum. Thus besides a photon emission, phononemission or absorption has to take place. GaP is an example of an indirect band-gap material.
The wavelength of the light emitted, and hence the color, depends on the band gap energy of the materials forming the p-n junction. The emitted photon energy is approximately equal to the band gap energy of the semiconductor. The following equation relates the wavelength and the energy band gap.

LED Materials

An important class of commercial LEDs that cover the visible spectrum are the III-V(see Appendix 5). ternary alloys based on alloying GaAs and GaP which are denoted by GaAs1- yPy.  InGaAlP is an example of a quarternary (four element) III-V alloy with a direct band gap. The LEDs realized using two differently doped semiconductors that are the same material is called a homo junction. When they are realized using different band gap materials they are called a hetero structure device hetero structure LED is brighter than a homo Junction LED.

LED Structure

The LED structure plays a crucial role in emitting light from the LED surface. The LEDs are structured to ensure most of the recombinations takes place on the surface by the following two ways.
• By increasing the doping concentration of the substrate, so that additional free minority charge carriers electrons move to the top, recombine and emit light at the surface.

• By increasing the diffusion length L = √ Dτ, where D is the diffusion coefficient and τ is the carrier life time. But when increased beyond a critical length there is a chance of re-absorption of the photons into the device. The LED has to be structured so that the photons generated from the device are emitted without being reabsorbed. One solution is to make the p layer on the top thin, enough to create a depletion layer. Following picture shows the layered structure. 
There aredifferent ways to structure the dome for efficient emitting LEDs are usually built on an n-type substrate, with an electrode attached to the p-type layer deposited on its surface. P-type substrates, while less common, occur as well. Many commercial LEDs, especially GaN/InGaN, also use sapphire substrate.

Saturday, 15 November 2014

itemprop='blogPost' itemscope='itemscope' itemtype='http://schema.org/BlogPosting'>

VACUUM CIRCUIT BREAKER( V C B )

electrical theory and electrical fundementals for all electrical related people . students , engineers, electrician #electricaltheorems,electrical,

                                  A vacuum circuit breaker is such kind of circuit breaker where the arc quenching takes place in vacuum. The technology is suitable for mainly medium voltage application. For higher voltage vacuum technology has been developed but not commercially viable. The operation of opening and closing of current carrying contacts and associated arc interruption take place in a vacuum chamber in the breaker which is called vacuum interrupter. The vacuum interrupter consists of a steel arc chamber in the centre symmetrically arranged ceramic insulators. The vacuum pressure inside a vacuum interrupter is normally maintained at 10 - 6 bar.
The material used for current carrying contacts plays an important role in the performance of the vacuum circuit breaker. CuCr is the most ideal material to make VCB contacts. Vacuum interrupter technology was first introduced in the year of 1960. But still it is a developing technology. As time goes on, the size of the vacuum interrupter is being reducing from its early 1960’s size due to different technical developments in this field of engineering. The contact geometry is also improving with time, from butt contact of early days it gradually changes to spiral shape, cup shape and axial magnetic field contact. The vacuum circuit breaker is today recognized as most reliable current interruption technology for medium voltage switchgear. It requires minimum maintenance compared to other circuit breaker technologies.

Advantages of Vacuum Circuit Breaker or VCB


Service life of vacuum circuit breaker is much longer than other types of circuit breakers. There is no chance of fire hazard as oil circuit breaker. It is much environment friendly than SF6 Circuit breaker. Beside of that contraction of VCB is much user friendly. Replacement of vacuum interrupter (VI) is much convenient

Operation of Vacuum Circuit Breaker



















The main aim of any circuit breaker is to quench arc during current zero crossing, by establishing high dielectric strength in between the contacts so that reestablishment of arc after current zero becomes impossible. The dielectric strength of vacuum is eight times greater than that of air and four times greater than that of SF6 gas. This high dielectric strength makes it possible to quench a vacuum arc within very small contact gap. For short contact gap, low contact mass and no compression of medium the drive energy required in vacuum circuit breaker is minimum. When two face to face contact areas are just being separated to each other, they do not be separated instantly, contact area on the contact face is being reduced and ultimately comes to a point and then they are finally de-touched. Although this happens in a fraction of micro second but it is the fact. At this instant of de-touching of contacts in a vacuum, the current through the contacts concentrated on that last contact point on the contact surface and makes a hot spot. As it is vacuum, the metal on the contact surface is easily vaporized due to that hot spot and create a conducting media for arc path. Then the arc will be initiated and continued until the next current zero.